Drill Summary

Drill Summary

Drill Summary

Drill Summary analyzes annular rings for drill holes and creates a report to list all the findings

Open Drill Summary

In Graphic Editor screen, select "Analysis" ，then select "Drill Summary" 。( Command：chklist_single )

Parameters

Parameters values can be changed in the respective fields and saved in ERF
All values and settings shown in this guide is by default
Parameters interface are shown below ：

Parameters

Drill Layer(s)

Select drill layers to be analyzed

Test Layer(s)

Seletc layers to be referenced

Max Annular

Set maximum annular ring size

Max Clearance

Set maximum clearance size

Set Range

Command：chklist_ erf_range

Set range value for each analysis check items
There are three types of analysis result: Critical, Warning or Safe
Default setting is avaialble for all parameters
Value can be changed in respective fields, and saved in ERF
See below picture for the Range interface：

Range

_outer__PTH__SPACE

Set analysis result range for PTH hole spacing to outer layer trace, surface and pad (overlapping areas are excluded)

_outer_NPTH__SPACE

Set analysis result range for NPTH hole spacing to outer layer trace, surface and pad (overlapping areas are excluded)

_outer__VIA__SPACE

Set analysis result range for VIA hole spacing to outer layer trace, surface and pad (overlapping areas are excluded)

_inner__PTH__SPACE

Set analysis result range for PTH hole spacing to inner layer trace, surface and pad (overlapping areas are excluded)

_inner_NPTH__SPACE

Set analysis result range for NPTH hole spacing to inner layer trace, surface and pad (overlapping areas are excluded)

_inner__VIA__SPACE

Set analysis result range for VIA hole spacing to inner layer trace, surface and pad (overlapping areas are excluded)

_smask__PTH__SPACE

Set analysis result range for PTH hole spacing to solder mask layer trace, surface and pad (overlapping areas are excluded)

_smask_NPTH__SPACE

Set analysis result range for NPTH hole spacing to solder mask layer trace, surface and pad (overlapping areas are excluded)

_smask__VIA__SPACE

Set analysis result range for VIA hole spacing to solder mask layer trace, surface and pad (overlapping areas are excluded)

_outer__PTH__AR

Set analysis result range for PTH hole spacing to outer layer annular ring

_outer_NPTH__AR

Set analysis result range for NPTH hole spacing to outer layer annular ring

_outer__VIA__AR

Set analysis result range for VIA hole spacing to outer layer annular ring

_inner__PTH__AR

Set analysis result range for PTH hole spacing to inner layer annular ring

_inner_NPTH__AR

Set analysis result range for NPTH hole spacing to inner layer annular ring

_inner__VIA__AR

Set analysis result range for VIA hole spacing to inner layer annular ring

_smask__PTH__AR

Set analysis result range for PTH hole spacing to solder mask layer annular ring

_smask_NPTH__AR

Set analysis result range for NPTH hole spacing to solder mask layer annular ring

_smask__VIA__AR

Set analysis result range for VIA hole spacing to solder mask layer annular ring

Run Drill Summary

Run Drill Summary Analysis after set up the parameters (Command：chklist_run)
Three buttons in the lower interface, each button runs the module at different area range
- Global ：Analyze all features in the layer ( Command：chklist_cupd )
- Screen ：Analyze all features in the screen display area( Command：chklist_cupd )
- Profile ：Analyze all features in profile frame( Command：chklist_cupd )

View Analysis Report

Click the " ＋ " button on the lower right to view analysis report ( Command：chklist_ res_show )

Result Viewer Form will be opened after click on the " ＋ " button

Result Viewer Form

In Result Viewer Form, Severity report will be displayed based on selected layers

View Detected Error in the Layout

In Result Viewer Form, click " <-- " or " --> " to view each error entry in the layout (See example below)

Click "Show All" will highlight all the error spots in the layout(See example below)

View Result Histogram for Analysis

Select an error entry, click the bar icon on lower right to open Result Histogram

Command ：chklist hist close

Command ：chklist hist show

Example of Result Histogram ：